Marine Sensors | Engine Management

Thermometrics Sensor Assemblies | Water Temperature Sensor (WTS)

Thermometrics Water Temperature Sensor (WTS) monitors the temperature of the coolant that is being pumped around the engine block to cool the engine to notify the driver of the vehicle if the engine starts to overheat. The goal is to relay an over-temperature engine temperature to the driver, so that the vehicle can be stopped and the engine switched off before the heat causes any permanent damage to the engine.
Thermometrics Sensor Assemblies | Type JR NTC Chip Thermistor in Eyelet Tag

Thermometrics Type JR NTC Chip Thermistors in Eyelet Tag are chip thermistors with insulated flexible wires and housed in an eyelet tag. They are suitable for surface temperature measurement. Typical applications include semi-conductor heatsinks and enclosure panels.
Thermometrics Sensor Assemblies | Transmission Fluid Temperature Sensor (TFT)

Thermometrics Transmission Fluid Temperature Sensor (TFT) measures the temperature of transmission fluid. It provides input to the control module to modify shift patterns for smoother shifting in automatic transmissions, and also provides over-temperature protection by locking the torque convertor.
Thermometrics Sensor Assemblies | Oil Temperature Sensor (OTS)

Thermometrics Oil Temperature Sensor (OTS) monitors the temperature of the engine oil in a vehicle and displays this measurement to the vehicle’s occupants. If a vehicle operates at too high a temperature, the engine can be in danger of damage.
Thermometrics Sensor Assemblies | Oil Pressure Switch

Thermometrics Oil Pressure Switch can be used in all vehicles to monitor the engine oil flow when the engine starts. It can detect oil pressure and enables the EMS ECU to check for the lack of oil. It can also send an alarm signal to the driver, helping to avoid engine damage due to overheating.
Thermometrics Sensor Assemblies | Mid-Range Temperature Probe

The Thermometrics Mid-Range Temperature Probe works in a variety of temperature applications in the appliance and industrial segment.
Thermometrics Sensor Assemblies | Inline Flow-Through Fluid Temperature Sensor

Thermometrics Inline Flow-Through Temperature Sensors monitor the temperature of a fluid that passes through it. A system control module receives this temperature reading and uses a control loop to control the overall system temperature. This could be engine temperature, heater temperature, industrial supply temperature, etc.
Thermometrics Sensor Assemblies | GE-1923 Outside Air Temperature Sensor (OAT)

Thermometrics GE-1923 Outside Air Temperature Sensor (OAT) measures the temperature outside of a vehicle's passenger compartment. It relays the outside air temperature to the controller of the automatic HVAC system. The controller uses this temperature to help control the interior temperature of the vehicle. The sensor also provides the vehicle occupants with temperature readings from outside the car.
Thermometrics Sensor Assemblies | GE-1711 / GE-1797 Engine Temperature Sensor (ETS)

Thermometrics GE-1711 / GE-1797 Engine Temperature Sensor (ETS) monitors the temperature of the coolant, oil or fuel being used in an engine.
Thermometrics Sensor Assemblies | GE-1571 Stainless Steel Sensor with Flying Leads

Thermometrics GE-1571 Stainless Steel Sensor with Flying Leads is designed to survive the vibration rigors of automotive, small gas engine, motorcycle and outboard engine applications. In addition to its ruggedness, this sensor offers fast response with a temperature rating of –40°C to 230°C.
Thermometrics Sensor Assemblies | Fuel Temperature Sensor (FTS)

Thermometrics Fuel Temperature Sensor (FTS) is designed to measure the temperature of a vehicle's fuel and relay this information to the engine control unit, so that it can optimize the air-to-fuel mix ratio, depending on what the fuel temperature is with respect to the intake air temperature. The sensor enables the vehicle to run at maximum efficiency based on temperature.
Thermometrics Sensor Assemblies | Exhaust Gas Recycle Temperature Sensor (EGR)

Thermometrics Exhaust Gas Recycle Temperature Sensor (EGR) is used to monitor the temperature at several locations in a diesel engine, as part of the engine control strategy. Available in both 150°C and 300°C temperature versions, the high temperature sensor is used in the exhaust gas, and the low temperature sensor is used in the intake air stream. Both are designed for fast response, optimized for thermal dissipation and suitable for high vibration and corrosive environments.
Thermometrics Sensor Assemblies | Exhaust Gas High Temperature Sensor

Thermometrics Exhaust Gas High Temperature Sensor monitors the temperature before and after SCR system in vehicle engines as part of the engine control strategy. It is designed for fast response, optimized for thermal dissipation and suitable for high vibration and corrosive environments.
Thermometrics Sensor Assemblies | Cylinder Head Temperature Sensor (CHT)

Thermometrics Cylinder Head Temperature Sensor is designed to take the place of one of the cylinder head bolts on a diesel engine. The sensor’s purpose is to measure the cylinder head temperature and to signal the vehicle’s operator if an engine overheats.
Thermometrics Sensor Assemblies | Combination Sensor

Thermometrics Combination Sensor is a smart combination intake manifold sensor capable of providing up to five measurements, including relative humidity, temperature, manifold pressure and barmetric pressure...
Thermometrics Sensor Assemblies | Accusolve Diesel Particulate Filter (DPF) Soot Sensor

Thermometrics Accusolve Diesel Particulate Filter (DPF) Soot Sensor utilizes radio frequency technology to enable accurate measurement of accumulated soot in the DPF, providing real-time soot loading data and real time closed loop control of the DPF regeneration process.
Thermometrics Sensor Assemblies | A-1737 Motor Coil Temperature Sensor

Thermometrics A-1737 Motor Coil Temperature Sensor provides temperature measurement of the motor coil to detect increases in current that could lead to failures, as well as to monitor temperature of motor windings to warn of over-temperature conditions.
Thermometrics NTC Thermistors | Radial Lead Type RL30

Thermometrics Type RL30 of Radial Lead NTC Thermistors consist of point-matched disc thermistors with bare lead wires. They are suitable for PCB and probe mountings with high sensitivity to changes in temperature and a wide operating range of -58°F to 302°F (-50°C to 150°C).
Thermometrics NTC Thermistors | Radial Lead Type RL20

Thermometrics Type RL20 of Radial Lead NTC Thermistors consist of point-matched disc thermistors with bare lead wires. They are suitable for PCB and probe mountings with high sensitivity to changes in temperature and a wide operating range of -58°F to 302°F (-50°C to 150°C).
Thermometrics NTC Thermistors | Radial Lead Type RL14

Thermometrics Type RL14 of Radial Lead NTC Thermistors consist of point-matched disc thermistors with bare lead wires. They are suitable for PCB and probe mountings with high sensitivity to changes in temperature and a wide operating range of -58°F to 302°F (-50°C to 150°C).

Page 1 of 3

Start
Prev
1
2
3
Next
End

Markets Menu

Products Menu

Industry Leaders for Over 75 Years

Offering industry leading domain expertise, rapid customization, world-class manufacturing capability and lasting customer relationships to deliver the greatest value in cost of ownership to our customers.