Thermometrics Type JR NTC Chip Thermistors in Eyelet Tag are chip thermistors with insulated flexible wires and housed in an eyelet tag. They are suitable for surface temperature measurement. Typical applications include semi-conductor heatsinks and enclosure panels.
Thermometrics Waterproof IP68 Temperature Sensors include Types JI and JIC NTC Thermistors. Both types are molded onto a flexible circular cable with the option of a stainless steel housing. Wide application range. Additional options for resistance-temperature characteristics, wire lengths and housing lengths.
Thermometrics Single Solar Sensors are mounted on a vehicle's IP panel near the front window and use the amount of outside sunlight entering the vehicle to assist in controlling the HVAC system. The single solar sensor has one photo diode cell inside, and is used in the independent type ATC, by sensing the amount of light left to right via angle light activating filters.
Thermometrics Oil Pressure Switch can be used in all vehicles to monitor the engine oil flow when the engine starts. It can detect oil pressure and enables the EMS ECU to check for the lack of oil. It can also send an alarm signal to the driver, helping to avoid engine damage due to overheating.
The Thermometrics Mid-Range Temperature Probe works in a variety of temperature applications in the appliance and industrial segment.
Thermometrics JS8746 Harsh Environment Temperature Sensor has been designed to address all aspects of temperature measurement for HVAC control systems in the container-ship market. Employing materials and build standards that enhance the sensor’s ability to withstand water ingression and degradation by the marine environment, the sensor meets statutory requirements for temperature measurement and performance expectations.
Thermometrics JS8741 Integrated Pipe Clip Surface Temperature Sensor monitors the temperature of a fluid or gas that passes through a pipe or tubing circulation system...
Thermometrics Active Incar Sensor indicates temperature in the cabin of passenger cars. Since it uses a fan to continuously draw air past the thermistor for an accurate temperature reading, it requires no venturi tube.
Thermometrics Inline Flow-Through Temperature Sensors monitor the temperature of a fluid that passes through it. A system control module receives this temperature reading and uses a control loop to control the overall system temperature. This could be engine temperature, heater temperature, industrial supply temperature, etc.
Thermometrics GE-1923 Outside Air Temperature Sensor (OAT) measures the temperature outside of a vehicle's passenger compartment. It relays the outside air temperature to the controller of the automatic HVAC system. The controller uses this temperature to help control the interior temperature of the vehicle. The sensor also provides the vehicle occupants with temperature readings from outside the car.
Thermometrics GE-1920 HVAC Refrigerant Temperature Sensor measures the refrigerant temperature both at the high pressure side and low pressure side of the line. The control module uses this information to maximize the performance of the HVAC system.
Thermometrics GE-1711 / GE-1797 Engine Temperature Sensor (ETS) monitors the temperature of the coolant, oil or fuel being used in an engine.
Thermometrics Evaporator Temperature Sensor is used to measure evaporator core temperature. An evaporator cools the refrigerant in the HVAC system. Since the evaporator core operates at temperatures very close to 0°C, it is important to have an accurate and robust thermistor to measure its temperature to prevent the core from freezing.
Thermometrics Evaporator Core Temperature Sensor measures evaporator core temperature in a vehicle's HVAC system so that it doesn’t freeze over, preventing a costly repair. The ultra fast response time aids in the HVAC system efficiency by enabling the evaporator core to operate closer to 0°C without the risk of a freeze over condition.
Thermometrics E-stat Controller is used in automobile air conditions to prevent the evaporator core from freezing.
The Thermometrics Duct Temperature Sensor indicates the ambient temperature of the automatic air conditioner system in the passenger car.
Thermometrics Duct Sensor is used to measure the temperature of the air that is emitted from the air ducts inautomobiles.
Thermometrics Dual Solar Sensor uses two photo diode cells to measure the intensity of the light that enters into the cabin of a vehicle.
Thermometrics Discharge Air Temperature Sensor (DAT) is used to measure the temperature of the air that is emitted from a vehicle's air ducts.
Thermometrics Cylinder Head Temperature Sensor is designed to take the place of one of the cylinder head bolts on a diesel engine. The sensor’s purpose is to measure the cylinder head temperature and to signal the vehicle’s operator if an engine overheats.
Page 1 of 4
CO2, Humidity & Dust Sensors
Thermal Validation & Monitoring
Offering industry leading domain expertise, rapid customization, world-class manufacturing capability and lasting customer relationships to deliver the greatest value in cost of ownership to our customers.
Follow us on Facebook
Follow us on YouTube
Follow us on LinkedIn